But it isn't exactly the least obscure product, either. It's been around since at least last year. For the record, this isn't a new product. I didn’t have to pay tax or shipping on my order. The NewerTech Snuglet can be purchased from OWC (Other World Computing at ) for $17.50 (normally $19.99). Help a friend with a newer MacBook (anything in the last couple years, most likely). Surprise them with one of these in their stocking. Get one set and share with another friend if you only have one laptop to use it on. Also, it's really hard to see, but the Snuglet is in there you can just barely notice its metallic edge within the charging port in this photo. Personally, this is just the way I like it. But you honestly don't have much leverage at this point, since your best point of leverage (from above or below) was reduced with the installation of the Snuglet. Imagine this: the least amount of force you can apply to detach the charger is just slightly less than that required to pull straight out (to counteract 100 percent of the force of the embedded magnet). While pulling sideways can reduce the necessary strength needed to detach the cable, it does need slightly more finesse to come loose with the Snuglet installed. After carefully repeated attempts, I’m satisfied that I would break (or risk breaking) the cable before it would detach in this direction of pull.
![apple macbook charger end piece apple macbook charger end piece](https://i.stack.imgur.com/H05gB.jpg)
![apple macbook charger end piece apple macbook charger end piece](https://img.grouponcdn.com/deal/eseCGQt9LE5fe6PXprzu/5n-960x576/v1/c700x420.jpg)
But the “worst” part is that a pull from the bottom or top of the cable in relation to the direction of its connection won’t do anything but lift up or pull your computer down. A pull straight out from your laptop (which is never unintentional) will still take the force necessary to counteract that of the magnet. A pull on the cable from the side will still cause it to release from the laptop, but it’ll take a harder pull that might drag your laptop first if pulled more slowly. By making it more difficult to remove your MagSafe charger, you’re limiting the “Safe” aspect of the charger’s design. But when you consider the problem you’re solving in doing so, well, let’s just say there are less annoying problems in life that I’d gladly pay $20 to fix. And when you consider that you’re paying $17.50 for a piece of metal that probably costs a few pennies to make, parting with that cash could be a lot to take in. The good news is that you likely won’t want to take the unit out - ever. If you were to lose it, I’m sure you could get creative with other thin pieces of metal (though reordering the Snuglet, which would include the removal tool, would be the obvious recommended route).
![apple macbook charger end piece apple macbook charger end piece](https://i.pinimg.com/originals/4a/bc/ab/4abcabec9ff4426a91d1051100805635.jpg)
NewerTech does include a removal tool, which is simply a fancy, thin metal hook that goes in and pulls the metal spacer out of your MacBook. Naturally, this means that no matter how many chargers you have floating around, you only need one Snuglet per laptop. You’ll notice that you can pull the charger out as many times as you want, and aside from the charger being more sturdily attached, the Snuglet also stays put in the computer. It's a bit surprising, but now you're done, as the Snuglet latches onto the magnet in the computer's port. Now, the Snuglet is installed into the laptop.
![apple macbook charger end piece apple macbook charger end piece](http://ecx.images-amazon.com/images/I/41qxTEdClwL._SY300_.jpg)
Plug your charger (with the Snuglet still around its metal tab) into your laptop just as you normally would. At this point, it’s not attached yet in any way. Open the package, slide one Snuglet ring (two are included) out of the packet, and slip it onto the end of your MagSafe 2 charger. Installing the Snuglet is so easy you almost can’t believe it. In minimizing the gap around the connector when it’s inserted, the Snuglet is a simple band that eliminates the ability for the connector to pop out if pulled on vertically, which solves the problem entirely, since the increased length of the metal piece of the normal MagSafe 2 connector (in relation to its predecessor) gives it too much leverage when pushed on from underneath. NewerTech apparently figured out that a small metal band held within the MagSafe 2 connector on the MacBook solely with its magnetic power could do the trick. These small nuisances can be dealt with a mild prescription of meditation, but what if you could pay $20 for the problem to disappear and still get some change back? We'd All Love a Solution Whether in bed epitomizing “Netflix and chill” or simply adjusting your laptop on your desk while getting your Wacom ready for editing duties, we always seem to accidentally disconnect our supposedly brilliantly designed MagSafe 2 connectors from our MacBooks.